Richmond Hill Attic Insulation & Air Sealing is an attic insulation and air sealing contractor serving Smiths Falls, ON, installing blown-in, spray foam and replacement insulation with 20+ years of experience. Every job starts with a free inspection and a blower door test, so the drafts in your older Smiths Falls home get fixed at the source.
Richmond Hill Attic Insulation & Air Sealing runs a blower door test on every home before any work begins.
The fan depressurizes the house so our technicians can measure how leaky it really is and where the air escapes.
The test runs again after installation, and both results are recorded for you to keep.
Since 2005, our crews have worked through older homes, non-standard attic layouts and tricky ventilation setups.
That adds up to 500+ attic projects across Richmond Hill and the GTA, with 150+ completed in 2026 alone.
A 97% client satisfaction rate shows the work holds up long after the crew leaves.
Every install follows Ontario Building Code standards, with R-values suited to freeze-thaw winters and summer heatwaves.
Before we start, you receive a written scope, confirmed material specs and a clear timeline.
A written warranty then covers both the materials and our workmanship.
A 4-person crew finishes most attics in 4 to 8 hours, so your day stays close to normal.
Hoses feed straight into the attic to keep dust out of your living space, and cleanup and haul-away are included.
The balance is only due after a senior supervisor walks through the finished attic with you.
We’ll call you back within 2 business days to book your free inspection.


Attic duct sealing and insulation completed for a 2000s two-storey a short drive from the Heritage House Museum. The owners wanted to know why their upstairs bedrooms swung from cold in winter to stuffy in summer, even with the air handler working hard in the attic.
A Duct Blaster test showed heavy leakage, so our crew replaced the torn flex runs with R-8 insulated duct, hung every line level on straps and sealed each joint and plenum takeoff with mastic. The owners said the upstairs finally feels like the rest of the house.
Turnaround Time: 1 day
Price: $2,900
Attic mould remediation and insulation replacement completed for a 1910s brick home a few blocks from the Rideau Canal locks. The owners wanted the musty smell upstairs gone for good. In the 1,050 sq ft attic, years of condensation had blackened the plank roof boards, mould spots dotted the rafters, and only a thin layer of grey loose-fill was left on the floor.
The Richmond Hill Attic Insulation & Air Sealing crew set up HEPA scrubbers, cleaned and treated every board with a mould-resistant coating, added baffles at the eaves, then blew in fresh fibreglass to R-60. The smell was gone within days.
Turnaround Time: 2 days
Price: $5,200


Attic duct sealing and insulation completed for a 2000s two-storey a short drive from the Heritage House Museum. The owners wanted to know why their upstairs bedrooms swung from cold in winter to stuffy in summer, even with the air handler working hard in the attic.
A Duct Blaster test showed heavy leakage, so our crew replaced the torn flex runs with R-8 insulated duct, hung every line level on straps and sealed each joint and plenum takeoff with mastic. The owners said the upstairs finally feels like the rest of the house.
Turnaround Time: 1 day
Price: $2,900
Our Attic Insulation and Air Sealing Services
Insufficient, compressed, or settled insulation allows heat to escape through the ceiling during winter and permits excessive heat transfer during summer. We improve coverage across attic floors, around framing, near ductwork, and beside wiring while protecting soffit vents and ventilation channels. More uniform insulation can help reduce heating and cooling demand and improve room-to-room comfort.
Smiths Falls includes older homes near the historic core as well as detached residences, renovated properties, and newer construction. These buildings may have different roof shapes, insulation materials, attic heights, and access limitations. Richmond Hill Attic Insulation & Air Sealing evaluates the existing assembly before recommending the most practical insulation improvement for the property.
Air leakage through plumbing penetrations, electrical openings, top plates, ceiling fixtures, duct connections, and attic hatches can undermine otherwise adequate insulation. We seal appropriate bypasses to reduce the escape of conditioned air and limit cold drafts at the ceiling plane. This work can improve insulation performance without requiring every attic to receive the same material or treatment.
Older Smiths Falls houses may include additions, converted porches, attached garages, and multiple renovation layers that create hidden leakage routes. Homes near the canal or established neighborhoods may also have irregular framing and limited attic access. Richmond Hill Attic Insulation & Air Sealing locates high-impact openings and seals them with careful attention to building materials and safety clearances.
An attic hatch can be a significant source of heat loss when its panel lacks insulation or its edges do not close tightly. We upgrade the hatch assembly with improved insulation, weatherstripping, perimeter sealing, and better continuity with the surrounding attic floor. A tighter hatch helps limit drafts while preserving convenient access for future inspections and maintenance.
Access locations vary among Smiths Falls homes, from hallway ceilings and bedroom closets to garage areas and stairwells. Richmond Hill Attic Insulation & Air Sealing works around the hatch size, trim, clearance, and interior finish when planning the installation. We use protective measures to help prevent dust, scuffs, and material damage inside occupied homes.
Reducing energy costs requires insulation and air sealing that work with, rather than obstruct, the roof-space ventilation system. We inspect soffit openings, baffles, roof vents, bathroom exhaust ducts, frost, staining, and damp insulation before completing attic improvements. Correcting air leakage and preserving airflow can help protect roof sheathing and framing from avoidable moisture exposure.
Smiths Falls’ cold winters, summer humidity, wooded lots, and waterways can contribute to varying attic conditions across the town. Richmond Hill Attic Insulation & Air Sealing coordinates insulation placement with ventilation protection and identifies issues that should be resolved before installation. This approach helps avoid covering up roof leaks, disconnected exhaust ducts, or condensation problems.
What You Need to Know
Smiths Falls, ON has a historic downtown and established neighborhoods alongside newer residential development, commercial areas, industrial properties, and rural land outside the central built-up area. Housing can include older wood-frame homes, brick residences, detached suburban properties, townhouses, and renovated buildings with additions. Age, renovation history, and roof geometry strongly affect insulation levels and air leakage.
Homes that have undergone multiple upgrades may contain mismatched insulation, unfinished attic sections, or ceiling penetrations added after the original construction. Richmond Hill Attic Insulation & Air Sealing reviews these details when planning energy-cost improvements for Smiths Falls, ON properties. Customers should mention high utility bills, cold rooms, ice buildup, drafts, prior roof work, or evidence of attic moisture during the consultation.
The Rideau Canal and Rideau River are defining features of Smiths Falls, and the community includes nearby waterways, mature vegetation, and areas with differing drainage characteristics. These conditions may affect exterior moisture, wind exposure, shade, and access around individual properties. Attic inspections should still distinguish roof leaks and site-related moisture from condensation caused by air moving through ceiling gaps.
During freezing weather, warm indoor air entering a cold attic can condense or form frost on roof components. Richmond Hill Attic Insulation & Air Sealing checks ceiling penetrations, exhaust ducts, soffit airflow, roof vents, and insulation condition before recommending work in Smiths Falls, ON. Proper preparation supports energy efficiency without increasing the risk of concealed moisture.
Highway 15 and Highway 43 provide important connections through and around Smiths Falls, while local streets serve established neighborhoods, downtown properties, and residential expansion areas. Winter snow, narrow streets, limited parking, long driveways, and homes with restricted attic entries can affect material movement and jobsite staging. Properties near the historic center may have tighter access than larger homes on peripheral or rural lots.
Before work begins, homeowners should discuss parking, material staging, attic-entry dimensions, interior walkways, and cleanup expectations. Richmond Hill Attic Insulation & Air Sealing coordinates delivery, equipment placement, protective coverings, insulation installation, and removal around each Smiths Falls, ON home. Clear planning helps control disruption and keep the project on schedule.
Smiths Falls, ON homeowners experience substantial heating demands during cold, snowy winters and may also face attic heat buildup during warm, humid summers. Proper insulation depth, continuous air sealing, unobstructed soffit airflow, and functional exhaust ventilation all contribute to lower energy use. A professional assessment should consider comfort, moisture, roof assembly, and mechanical details together.
Chimneys, flues, recessed fixtures, electrical wiring, ductwork, and other heat-producing or mechanical components require appropriate clearances. Richmond Hill Attic Insulation & Air Sealing incorporates safe installation practices and ventilation protection into attic projects in Smiths Falls, ON. Ask for a written scope that explains inspection, preparation, air sealing, insulation installation, and cleanup.
Many of Smiths Falls’ older brick homes near the Rideau Canal were balloon-framed, with open wall cavities that send warm air straight into the attic. We seal those wall tops with rigid foam and fire-rated sealant, flag any knob-and-tube wiring for an Electrical Safety Authority check, then blow in cellulose or fibreglass to R-60, with baffles at every eave to help stop ice dams.
We also serve these nearby communities: