Richmond Hill Attic Insulation & Air Sealing provides attic insulation and air sealing throughout Carleton Place, ON, and closes out every job with a senior supervisor walking the finished attic with you. From heritage brick homes along the Mississippi River to the town’s newer subdivisions, each project starts with a free inspection and a blower door test.
Richmond Hill Attic Insulation & Air Sealing runs a blower door test on every home before any work begins.
The fan depressurizes the house so our technicians can measure how leaky it really is and where the air escapes.
The test runs again after installation, and both results are recorded for you to keep.
Since 2005, our crews have worked through older homes, non-standard attic layouts and tricky ventilation setups.
That adds up to 500+ attic projects across Richmond Hill and the GTA, with 150+ completed in 2026 alone.
A 97% client satisfaction rate shows the work holds up long after the crew leaves.
Every install follows Ontario Building Code standards, with R-values suited to freeze-thaw winters and summer heatwaves.
Before we start, you receive a written scope, confirmed material specs and a clear timeline.
A written warranty then covers both the materials and our workmanship.
A 4-person crew finishes most attics in 4 to 8 hours, so your day stays close to normal.
Hoses feed straight into the attic to keep dust out of your living space, and cleanup and haul-away are included.
The balance is only due after a senior supervisor walks through the finished attic with you.
We’ll call you back within 2 business days to book your free inspection.


Attic mould remediation completed for an 1890s brick home a few blocks from Carleton Place Town Hall. The owners noticed a musty smell upstairs and dark patches spreading across the roof boards after years of poor venting. In the 950 sq ft attic, the original plank boards were mouldy along the north slope, with a few sections soft enough that the roofer replaced them.
Our crew HEPA-vacuumed and treated every board, sealed them with a mould-resistant coating and fitted baffles to restore airflow at the eaves. The musty smell was gone by the end of the week.
Turnaround Time: 2 days
Price: $4,800
Cathedral ceiling insulation upgrade completed for a 1920s storey-and-a-half a short walk from Riverside Park on the Mississippi River. The owners opened up their upstairs bedroom ceiling to create a vaulted room with new pot lights and wanted it to stay warm through Lanark County winters.
The Richmond Hill Attic Insulation & Air Sealing crew sprayed closed-cell foam about 5.5 inches deep across the roof deck, sealing tightly around each airtight light housing, and fitted batts in the gable wall. The vaulted bedroom now holds its heat as well as the rest of the house.
Turnaround Time: 2 days
Price: $7,400


Spray foam attic insulation completed for a 2010s two-storey a few minutes from the Carleton Place Canoe Club. The owners’ bonus room over the garage ran cold all winter and stuffy all summer. In the 800 sq ft space, the heating ducts ran through the open eaves behind the knee walls, losing heat to the outdoors before it ever reached the room.
Our crew sprayed closed-cell foam across the roof deck and sealed off the eave vents, bringing the ducts inside the insulated space. The bonus room now stays within a degree of the rest of the house.
Turnaround Time: 2 days
Price: $6,100
Blown-in insulation can improve thermal coverage across irregular attic floors, narrow framing bays, and areas where existing material has settled. We install the material to create more consistent protection over heated rooms while working around trusses, ductwork, wiring, and attic access points. This approach can help reduce temperature swings between upper rooms and the rest of the home.
Carleton Place properties range from older village homes with uneven attic spaces to newer subdivision residences with larger, more structured roof systems. Richmond Hill Attic Insulation & Air Sealing evaluates attic depth, existing material, ventilation paths, and obstructions before determining whether blown-in insulation is suitable. Proper preparation helps prevent blocked soffits, concealed hazards, and uneven coverage.
Drafts above bedrooms, hallways, and top-floor living areas often originate from small openings that are difficult to identify from inside the home. We inspect attic hatches, plumbing penetrations, electrical openings, framing joints, ceiling fixtures, and duct connections for pathways that allow conditioned air to escape. Finding these locations before installing additional insulation helps ensure the upgrade addresses the cause of discomfort.
Older properties around the historic core may contain irregular framing, additions, and multiple generations of repairs. Newer homes can also develop leakage around recessed lighting, bathroom fans, wiring routes, and access panels. Richmond Hill Attic Insulation & Air Sealing uses a detail-focused assessment process to prioritize the openings most likely to affect comfort and energy performance.
Cold bedrooms, chilly ceiling areas, and rooms that require more heating than the rest of the home can indicate missing insulation or gaps in the attic air barrier. We trace comfort complaints to insulation depth, compressed material, exposed sections, thermal bridging, and air leakage above the affected space. Correcting the attic-side cause can provide a more direct solution than continually adjusting the thermostat.
Summer discomfort can also occur when insufficient attic insulation allows roof heat to transfer into upper-level rooms. Richmond Hill Attic Insulation & Air Sealing connects room-specific temperature patterns with the attic’s layout, ventilation, insulation condition, and ceiling penetrations. Our recommendations are structured around measurable building conditions and the homeowner’s comfort priorities.
Frost, staining, musty odors, damp insulation, and darkened roof sheathing may indicate moisture entering or accumulating in the attic. We inspect air leakage points, bathroom exhaust ducts, soffits, roof vents, baffles, and insulation condition before recommending corrective work. Addressing these factors helps protect the roof assembly while improving the performance of the insulation.
Carleton Place’s cold winters, snowfall, freeze-thaw cycles, river setting, and summer humidity can expose ventilation weaknesses over time. Richmond Hill Attic Insulation & Air Sealing coordinates air sealing and insulation placement with moisture-control considerations so new material does not conceal unresolved problems. We also identify conditions that may require repair or further evaluation before the attic upgrade proceeds.
Carleton Place, ON includes a historic downtown, established residential neighborhoods, newer subdivisions, and rural properties extending beyond the central community. Housing types include older wood-frame homes, detached suburban residences, townhouses, semi-detached properties, and larger homes on spacious lots. Differences in construction age, roof geometry, and renovation history can affect attic access, insulation depth, air leakage, and ventilation.
Additions, dormers, skylights, finished upper floors, bathroom upgrades, and electrical renovations may alter the original ceiling plane. Richmond Hill Attic Insulation & Air Sealing reviews these details when preparing a home comfort plan for Carleton Place, ON. Homeowners should identify drafty rooms, high utility bills, previous insulation work, roof leaks, and areas with recurring winter frost.
The Mississippi River is central to Carleton Place’s geography, historic development, and community identity. Nearby properties may have different vegetation, wind exposure, drainage patterns, and seasonal moisture conditions than homes located farther from the river. These site characteristics can provide useful context when assessing leaks, staining, pest activity, and attic ventilation concerns.
Warm indoor air that escapes through ceiling penetrations can condense on cold roof surfaces during winter. Richmond Hill Attic Insulation & Air Sealing examines insulation levels, air-sealing deficiencies, exhaust-duct terminations, soffit airflow, and roof vents before recommending work in Carleton Place, ON. Correcting uncontrolled air movement is essential for improving comfort without increasing moisture risk.
Highway 7 provides a major connection between Carleton Place, Ottawa, and communities to the west, while Highway 15, County Road 29, and local streets serve residential and rural areas. Highway approaches, downtown traffic, schools, commercial corridors, and ongoing subdivision growth can affect arrival times and material staging. Long driveways, attached garages, narrow side access, and townhouse layouts may require additional planning.
Before work begins, the contractor should confirm where materials will be placed, how workers will reach the attic, and which rooms require protective coverings. Richmond Hill Attic Insulation & Air Sealing coordinates staging, access, equipment placement, removal, installation, and cleanup around the specific property in Carleton Place, ON. Clear preparation helps keep the project efficient and minimizes disruption inside the home.
Properties in Carleton Place, ON experiences snowy winters, freezing temperatures, freeze-thaw conditions, warm summers, and periods of humidity. These seasonal patterns make insulation coverage, attic air sealing, soffit protection, exhaust ventilation, and moisture management important parts of a complete comfort improvement. An estimate should explain how the proposed work addresses both heat transfer and air movement.
Chimneys, flues, electrical wiring, recessed fixtures, ductwork, and attic hatches require safe treatment during insulation installation or removal. Richmond Hill Attic Insulation & Air Sealing accounts for clearances, ventilation channels, material handling, and cleanup when planning projects in Carleton Place, ON. Customers should confirm that the scope includes attic preparation and inspection rather than simply adding insulation over existing conditions.
Carleton Place’s heritage storey-and-a-half homes near the Mississippi River often have empty knee walls and sloped ceilings behind their dormers, while the town’s newer subdivisions tend to have thin, settled builder insulation. We use thermal imaging to find the cold voids, dense-pack cellulose into knee walls and sloped ceilings, seal the attic floor around wiring and wall tops, then blow insulation to R-60.
We also serve these nearby communities: